Release Notes PIKO SmartProgrammer und PIKO SmartTester

« Back to FAQ / information page

09.10.2024 Update | PIKO SmartProgrammer App Version 1.2.10.0 > Version 1.2.11.0

Release Notes:

NEW: general

New function keys RailCom symbols added (Programming -> Function keys)

NEW: PSD XP 5.1

Function -StepSequenzer- available. Special mapping function for storing several functions that can be switched through one after the other (Programming -> Function mapping)
SUSI brake command (Programming -> Information -> SUSI)
Energy storage setting (Programming -> Information -> Energy storage)
Switch off outputs when coupled via SUSI (Programming -> Equipment -> A...)
Linear conversion from FS28 -> FS128 can be activated (Programming -> Information -> Address -> DCC)
Function mapping to SUSI binary state (Programming -> Information -> SUSI)

Bugfixes:

Problem G sound was not copied fixed
Sound volume was always set to 1 after editing
Problem with decoder recovery tool for XP 5.1 G decoder fixed

Important Note: This is the last version released for Windows 7 & 8. All future versions require at least Windows 10.

^{Questions? Mail us:}

06.12.2023 Update | PIKO SmartProgrammer App Version 1.2.9.0 > Version 1.2.10.0

Release Notes:

NEW:

PIKO TrainBus: The new PIKO TrainBus in our multi-part models offers extended light functions and a power head changeover for braking sections. As of this app version, it is possible to customize the function key assignment and light control for models controlled via the TrainBus.

Bugfixes:

mfx calibration: Connection to the decoder in the SmartTester is checked before calibration.
SmartDecoder 4.1: Project templates adjusted, the CVs required for analog operation were not set correctly.
Decoder restores: Factory CVs are set.

^{Questions? Mail us:}

31.03.2023 Update | PIKO SmartProgrammer App Version 1.2.8.0 > Version 1.2.9.0

Release Notes:

NEW:

mfx calibration - Tool to improve the mfx logon

If a vehicle with a PSD XP5.1 does not, or only incompletely, log on to an mfx-capable command station, an improvement can be achieved by the new mfx calibration.
For this, the "expert mode" (header blue) must be activated in the PSP app.
The XP 5.1 decoder must be plugged into the PIKO SmartTester, so it cannot be calibrated in the loco via the track output!
In the PSP app goto the menu "Info" and there into the sub menu "Tools".

^{Questions? Mail us:}

06.02.2023 Update | PIKO SmartProgrammer App Version 1.2.7.0 > Version 1.2.8.0

Release Notes:

NEW:

Light scheme

You can display a graphic for the Piko locomotive in the Expert mode in the area FunktionMapping, in which the light wiring of the locomotive is shown graphically.

^{Questions? Mail us:}

13.10.2022 Update | PIKO SmartProgrammer App Version 1.2.6.0 > Version 1.2.7.0

Release Notes:

Bugfixes:

Crash when loading sound samples
SmartDecoder XP 5.1 for the NEM 652 (8-pin) problem with sound transmission fixed

New (New settings in relation with firmware 1.7.X for SmartDecoder XP 5.1):

The input pin (GPIO/C) of PluX22 can now be used as a wheel sensor for cylinder steam noise as well as a trigger for function keys or shuttle operation
Motor functionality can be switched off, for the use of sound decoders in cars
Settings for the evaluation of the SUSI status information to influence the driving behavior

New (Product search for alternative part numbers):

You can search for locomotive numbers in the project search to find a suitable sound project

^{Questions? Mail us:}

08.08.2022 Update | PIKO SmartProgrammer App Version 1.2.5.0 > Version 1.2.6.0

Release Notes:

Bugfixes:

Large project files could not always be opened
In steam locomotive sound projects for the SmartDecoder XP 5.1 there were dropouts in the driving sound
No symbol was displayed for the sound "compressor

New (support for PIKO SmartDecoder XP 5.1 extended):

Light effect "TV-Simulation" added
A symbol for the mfx protocol can be stored up to F32

^{Questions? Mail us:}

02.02.2022 Update | PIKO SmartProgrammer App Version 1.2.4.0 > Version 1.2.5.0

Release Notes:

Bugfixes:

Crash with project file for function decoder fixed

New/Other Changes:

Russian added

Programming XP 5.1
-> Motor control CV 62 Bit 4 & 5: Settings under Program Decoder -> Drive Behaviour -> Controller -> Advanced Parameters
-> "Invert Servo Direction" added

Support of the PIKO SmartDecoder XP 5.1 PluX16/NEM 652
-> Our PIKO SmartDecoder XP 5.1 are now available for the first locomotives with 8-pin NEM652 interface. From this app version on, these can be programmed, provided with projects and their firmware can be updated.

^{Questions? Mail us:}

14.12.2021 Update | PIKO SmartProgrammer App Version 1.2.3.0 > Version 1.2.4.0

Release Notes:

New/Other Changes:

French added
Czech added
Support SmartDecoder XP 5.1 Firmware 1.2.0
The version of the decoder firmware 1.2.0 contains structural adjustments. More information can be found in the release notes for the decoder firmware or in the FAQs. Your XP 5.1 decoder is automatically updated to the new version.
WLAN signal transmission power
The transmission power of the PSP can be set under Settings PSP Settings WLAN.

For locomotives with buffer memory it may be necessary to have longer pauses when writing some settings. This option is shown for example when writing projects.
Support of SmartDecoder XP 5.1 Next18
Projects with many part numbers shortened.
@iOS: Faulty CV display fixed.
Problem with project files in connection with function decoders fixed.

^{Questions? Mail us:}

10.11.2021 Update | PIKO SmartProgrammer App Version 1.2.2.0 > Version 1.2.3.0

Release Notes:

Bugfixes:

The CVs for the alternative sound sequences were offset by 1 CV in XP 5.1
Crash fixed, if PSP firmware version is not yet able to calibrate RailCom
Crash fixed, when starting a shuttle route, if no train address/switch address was entered yet
When copying decoder information to the clipboard, a crash could occur

New:

Polish added
Copies of current settings to factory settings
Expert mode: Under [Decoder Programming] -> [Information] -> [Factory Settings], the [Set] icon can be used to overwrite the factory settings with the current settings
Information text for the alternative sound sequences
Under [Decoder Programming] -> [Sound] -> [General], an (i) is displayed (if available) with information on the use of the alternative sound sequence CVs/variables
Search for XP 5.1 projects simplified
For our new SmartDecoder XP 5.1 you can already find some projects in the app. The projects are marked with a red XP 5.1 symbol. To make it easier for you to find these projects, we have extended the search function. You can add "XP 5.1" as a filter in the search field next to the series designation or project number.
Acceleration when reading from the decoder

^{Questions? Mail us:}

22.10.2021 Update | PIKO SmartProgrammer App Version 1.2.1.0 > Version 1.2.2.0

Release Notes:

Bugfixes:

The reading in of the decoder can be cancelled at [Test decoder].
Program crash when reading in decoders fixed.
With SmartDecoder XP 5.1 only the usable function keys are displayed in the control panel.
Locomotive symbols were not always displayed in the project overview.
Program crash when opening project files fixed.
With SmartDecoder XP 5.1 the function key/output designation was not always saved.

^{Questions? Mail us:}

28.09.2021 Update | PIKO SmartProgrammer App Version 1.2.0.0 > Version 1.2.1.0

Release Notes:

Bugfixes:

Threshold values for brake squeal and curve squeal were interchanged
Designation of sound slots were not saved after user change
Some XP 5.1 decoders were not correctly recognised by type Non-Sound/Sound
The app crashed when playing sound samples
The app froze when no internet connection was available when replacing sounds
On Windows, the taskbar icon always remained green after completing an update process.

Other:

The ReleaseNotes are displayed when updating the firmware of decoders, click (i)
The PSP beeps after a decoder firmware update
Italian translation

^{Questions? Mail us:}

24.08.2021 Update | PIKO SmartProgrammer App Version 1.1.11.0 > Version 1.2.0.0

Release Notes:

New:

Support SmartDecoder XP 5.1:

The new PIKO SmartDecoder XP 5.1 can be used via the main menu.
Testing the decoder: You now have more than the usual 29 function keys (F0 - F28) available with the SmartDecoder XP 5.1.
Decoder Programming: You can set all the CVs of your SmartDecoder XP 5.1 graphically via this menu. We have provided you with useful information about the respective setting in many places via the (i) symbol.
Projects: The first locomotive projects for the SmartDecoder XP 5.1 are available. These projects are marked with a red symbol [XP 5.1]. 4.1 projects are constantly being revised to adapt them to the functions of the XP 5.1 decoder.

Custom sounds in PIKO projects:

Applies to SmartDecoder 4.1 Sound and XP 5.1 Sound. You can fill unused sound slots with your own sounds. Select a sound slot in the app and click on the [Replace] symbol in the upper right corner. You can use a .wav or .mp3 file as the source. The PIKO SmartDecoder plays mono sound. Only the 1st sound channel (linker channel) of the file is used. This function is only available under Windows for the time being.

PSP firmware update:

For the communication with the SmartDecoder XP 5.1 it is necessary to update the firmware of the SmartProgrammer. This is only possible under Microsoft Windows and with a USB connection.

^{Questions? Mail us:}

04.02.2021 Update | PIKO SmartProgrammer App Version 1.1.10.0 > Version 1.1.11.0

Release Notes:

New:

With PSP firmware 0.62 it is possible to transfer data to SmartDecoder with the latest version. The warning that no factory settings can be written has been removed again
Connection to the first PSP found was established although this setting was switched off.
For CV 1, 17, 18 and 29, the system no longer switches to ACK mode.
In the control panel, CVs can now be set using XPOM. Address 0 is valid for POM and XPOM.
The update process for the PSP did not update the installed version after the update. A connection to the PSP could only be restored after an app restart.

^{Questions? Mail us:}

10.11.2020 Update | PIKO SmartProgrammer App Version 1.1.9.0 > Version 1.1.10.0

Release Notes:

New:

Decoder without factory settings
A warning message is displayed if a decoder has the function "Writing factory settings" is not available.

Print
You can output the function key assignment using the print function. In Expert mode, the switched functions/sounds are displayed in addition to the function keys.

Filter setting
You can output the function key assignment using the print function.

^{Questions? Mail us:}

14.10.2020 Update | PIKO SmartProgrammer App Version 1.1.8.0 > Version 1.1.9.0

Release Notes:

New:

PIKO Light Controller
Some PIKO locomotives of N and TT gauge have an additional light controller. This light controller has separate dimming settings for the light outputs. Function keys are assigned to the light controller outputs in the function mapping. The settings for the light controller are loaded directly from the projects together with the driving and sound parameters. You can only make settings on the light controller if the SmartDecoder 4.1 is located in the locomotive.

Function decoder
The PIKO function decoders are also recognised by the app with a firmware < 9.

CV lists export [expert view]
In the "Programming decoders" section of the CVs menu, under "CV Export" you have the option of exporting a CV list with all decoder CVs as a table (CSV file). Furthermore, in the same menu under "Changed CVs" you can view a list of all values changed in the current programming session.

Multiple Smart Programmers [Expert View]
If several PIKO SmartProgrammers are connected to your device, the app will always connect to the first one found. You can now deactivate this behaviour in the settings. If the setting "Connect to PSP directly" is set to "Off", you will always be shown a list of available SmartProgrammers.

^{Questions? Mail us:}

10.09.2020 Update | PIKO SmartProgrammer App Version 1.1.7.0 > Version 1.1.8.0

Release Notes:

New:

Function decoder
The PIKO function decoder #56124 / #56126 can be programmed with projects.
Projects for the function decoder are marked with an [F] in the project list.
The configuration of the function decoder can be modified and tested.

Edit sound module
If the sound module is connected to the PSP/PST you can set this via [Program Decoder].
If the sound module is connected to the decoder and installed in the locomotive, this already worked.

Optional more compact view
In the settings, the user can specify that buttons should be displayed smaller.

Progress bar with percentage
When writing sound projects, the progress in percent is displayed below the progress bar.

^{Questions? Mail us:}

06.04.2020 Update | PIKO SmartProgrammer App Version 1.1.6.0 > Version 1.1.7.0

Release Notes:

New:

Dutch
Sound volume: Project-dependent maximum
Write sound switching stages from project to decoder
Decoder details shows info about SoundModul on the decoder
Potentiometer setting for sound module / G-decoder

Bug-Fix:

Fixed bug when switching between decoder details and tester
Loading of product information and display of function key and sound slot designations
The function mappings were not saved/loaded in the project file
WLAN Settings Crash when saving

^{Questions? Mail us:}

27.03.2020 Update | PIKO SmartProgrammer App Version 1.1.5.0 > Version 1.1.6.0

Release Notes:

New:

Sound projects can be transferred to a combination of SmartDecoders without sound and PIKO sound module
G-Decoder
Settings for servos
Consumption simulation for servo 4
Energy storage parameters
Braking deceleration in case of emergency stop
Next18 decoder: Setting for SUSI as SUSI/A3 and SUSI/A4
Function mapping: added the functions "sound off" and "volume control" for sound decoders
Decoder Reset in Expert Mode
Basic settings for your PSP (WLAN / voltage)

Bug-Fix:

Function mapping more clearly arranged
Function key replacement with warning message if the function changes after replacement
Project list sorted by numbers in ascending order

^{Questions? Mail us:}

01.03.2020 Update | PIKO SmartProgrammer App Version 1.1.4.0 > Version 1.1.5.0

Release Notes:

New:

Sound projects can be transferred to Non-Sound Decoder & the PIKO Sound-Modul
In expert mode, non-sound projects can be transferred to sound decoders !! Attention !! Previous sound remains.

Bug-Fix:

Loading of all decoder settings stabilized
Improved display of the project list
Mfx function symbols are taken from projects and can be changed
The extended flashing generator was extended by the parameters for phase inversion
Improved on/off switch in the display